LTC1669 10-Bit Rail-to-Rail Micropower DAC with I2C Interface DESCRIPTION FEATURES n n n n n n n n n n n n Micropower 10-Bit DAC in SOT-23 Low Operating Current: 60A Ultralow Power Shutdown Mode: 12A 2-Wire Serial Interface Compatible with I2CTM Selectable Internal Reference or Ratiometric to VCC Maximum DNL Error: 0.75LSB 8 User Selectable Addresses (MSOP Package) Single 2.7V to 5.5V Operation Buffered True Rail-to-Rail Voltage Output Power-On Reset 1.5V VIL and 2.1V VIH for SDA and SCL Small 5-Lead TSOT-23 and 8-Lead MSOP Packages APPLICATIONS n n n n n n Digital Calibration Offset/Gain Adjustment Industrial Process Control Automatic Test Equipment Arbitrary Function Generators Battery-Powered Data Conversion Products The LTC(R)1669 is a 10-bit voltage output DAC with true buffered rail-to-rail output voltage capability. It operates from a single supply with a range of 2.7V to 5.5V. The reference for the DAC is selectable between the supply voltage or an internal bandgap reference. Selecting the internal bandgap reference will set the full-scale output voltage range to 2.5V. Selecting the supply as the reference sets the output voltage range to the supply voltage. The part features a simple 2-wire serial interface compatible with I2C that allows communication between many devices. The internal data registers are double buffered to allow for simultaneous update of several devices at once. The DAC can be put in low current power-down mode for use in power conscious systems. Power-on reset ensures the DAC output is at 0V when power is initially applied, and all internal registers are cleared. The LTC1669 is pin-for-pin compatible with the LTC1663. For SMBus-compatible designs, please refer to the LTC1663. L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. BLOCK DIAGRAM 4 (5) Differential Nonlinearity (DNL) VCC 1.25V BANDGAP REFERENCE 1.0 VREF = VCC = 5V TA = 25C 0.8 0.6 REFERENCE SELECT ERROR (LSB) 0.4 10-BIT DAC LATCH 10-BIT BUFFERED VOUT DAC COMMAND LATCH MSOP PACKAGE ONLY VOUT 3 (8) 0.2 0 -0.2 -0.4 -0.6 -0.8 INPUT LATCH -1.0 0 (6) AD0 (2) AD1 (3) AD2 28 156 384 512 640 768 896 1024 CODE 1669 G02 2-WIRE INTERFACE SDA SCL GND 1 (1) 5 (4) 2 (7) 1669 BD NOTE: PIN NUMBERS IN PARENTHESES REFER TO THE MSOP PACKAGE 1669fa 1 LTC1669 ABSOLUTE MAXIMUM RATINGS (Note 1) VCC to GND .............................................. - 0.3V to 7.5V SDA, SCL ................................................. -0.3V to 7.5V AD0, AD1, AD2 (MSOP Only) ........-0.3V to (VCC + 0.3V) VOUT .............................................-0.3V to (VCC + 0.3V) Operating Temperature Range LTC1669C ............................................... 0C to 70C LTC1669I............................................. -40C to 85C Storage Temperature Range.................. -65C to 150C Lead Temperature (Soldering, 10 sec) ................. 300C PIN CONFIGURATION TOP VIEW TOP VIEW SDA AD1 AD2 SCL 1 2 3 4 8 7 6 5 VOUT GND AD0 VCC SDA 1 5 SCL GND 2 VOUT 3 MS8 PACKAGE 8-LEAD PLASTIC MSOP 4 VCC S5 PACKAGE 5-LEAD PLASTIC SOT-23 TJMAX = 125C, JA = 250C/W TJMAX = 125C, JA = 150C/W ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LTC1669CMS8#PBF LTC1669CMS8#TRPBF LTAHV 8-Lead Plastic MSOP 0C to 70C LTC1669IMS8#PBF LTC1669IMS8#TRPBF LTAHX 8-Lead Plastic MSOP -40C to 85C LTC1669-8CMS8#PBF LTC1669-8CMS8#TRPBF LTAHT 8-Lead Plastic MSOP 0C to 70C LTC1669-8IMS8#PBF LTC1669-8IMS8#TRPBF LTAHU 8-Lead Plastic MSOP -40C to 85C TAPE AND REEL (MINI) TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LTC1669CS5#TRMPBF LTC1669CS5#TRPBF LTAHW 5-Lead Plastic TSOT-23 0C to 70C LTC1669-1CS5#TRMPBF LTC1669-1CS5#TRPBF LTAHR 5-Lead Plastic TSOT-23 0C to 70C TRM = 500 pieces. Consult LTC Marketing for parts specified with wider operating temperature ranges. Consult LTC Marketing for information on lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 1669fa 2 LTC1669 ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 2.7V to 5.5V, VCC set as reference, VOUT unloaded, unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS DAC l 10 Bits Monotonicity (Note 2) l 10 Bits Differential Nonlinearity Guaranteed Monotonic (Note 2) l 0.2 0.75 LSB 0.5 2.5 LSB 10 30 mV Resolution DNL INL Integral Nonlinearity (Note 2) l VOS Offset Error Measured at Code 20 l l l VOSTC Offset Error Temperature Coefficient FSE Full-Scale Error Reference Set to VCC Reference Set to Internal Bandgap 15 VOUT DAC Output Span Reference Set to VCC Reference Set to Internal Bandgap 0 to VCC 0 to 2.5 VFSTC Full-Scale Voltage Temperature Coefficient Reference Set to VCC Reference Set to Internal Bandgap 30 50 V/C V/C PSRR Power Supply Rejection Ratio Reference Set to Internal Bandgap, Code = 1023 0.4 LSB/V 3 3 V/C 15 15 LSB LSB V V Power Supply l VCC Positive Supply Voltage ICC Supply Current VCC = 3V (Note 3) VCC = 5V (Note 3) l l ISD Supply Current in Shutdown Mode (Note 3) Short-Circuit Current (Sourcing) 2.7 5.5 V 60 75 100 125 A A l 12 24 A VOUT Shorted to GND, Input Code = 1023 l 25 100 mA Short-Circuit Current (Sinking) VOUT Shorted to VCC, Input Code = 0 l 30 120 mA Output Impedance to GND Input Code = 0, VCC = 5V Input Code = 0, VCC = 5V In Shutdown Mode 65 150 500 k Output Impedance to VCC Input Code = 1023, VCC = 5V Input Code = 1023, VCC = 5V 80 120 Voltage Output Slew Rate Rising (Notes 4, 5) Falling (Notes 4, 5) 0.75 0.25 V/s V/s Voltage Output Settling Time To 0.5LSB (Notes 4, 5) Op Amp DC Performance AC Performance 30 Digital Feedthrough Digital-to-Analog Glitch Impulse 1LSB Change Around Major Carry s 0.75 nV*s 70 nV*s Digital Inputs SCL, SDAs VIH High Level Input Voltage l VIL Low Level Input Voltage l 2.1 V 1.5 V VLTH Logic Threshold Voltage ILEAK Digital Input Leakage VCC = 5.5V and 0V, VIN = GND to VCC l 1.8 1 A V CIN Digital Input Capacitance (Note 7) l 10 pF IPULLUP = 3mA l 0.4 V Digital Output SDA VOL Digital Output Low Voltage 1669fa 3 LTC1669 ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 2.7V to 5.5V, VCC set as reference, VOUT unloaded, unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX 0.5 1.5 UNITS Address Inputs AD0, AD1, AD2 (MSOP Only) l IUP Address Pin Pull-Up Current VIN = 0V VIH High Level Input Voltage l VIL Low Level Input Voltage l A VCC - 0.3 V 0.8 V TIMING CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 2.7V to 5.5V, VCC set as reference, VOUT unloaded, unless otherwise noted. SYMBOL PARAMETER MIN TYP MAX UNITS Timing Characteristics (Notes 6, 7) fSCL Clock Operating Frequency tBUF Bus Free Time Between Stop and Start Condition 100 kHz 4.7 s tHD, STA Hold Time After (Repeated) Start Condition 4 s tSU, STA Repeated Start Condition Setup Time 4.7 s tSU, STO Stop Condition Setup Time 4 s tHD, DAT (IN) Data Hold Time (Input) 0 tHD, DAT (OUT) Data Hold Time (Output) 225 tSU, DAT Data Setup Time 250 ns tLOW Clock Low Period 4.7 s tHIGH Clock High Period 4 s tf Clock, Data Fall Time 20 300 ns tr Clock, Data Rise Time 20 1000 ns Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Nonlinearity and monotonicity are defined from code 20 to code 1003 (full scale). See Applications Information. ns 500 3450 ns Note 3: Digital inputs at 0V or VCC. Note 4: Load is 10k in parallel with 100pF. Note 5: VCC = VREF = 5V. DAC switched between 0.1VFS and 0.9VFS, i.e., codes k = 102 and k = 922. Note 6: All values are referenced to VIH and VIL levels. Note 7: Guaranteed by design and not subject to test. 1669fa 4 LTC1669 TYPICAL PERFORMANCE CHARACTERISTICS Integral Nonlinearity (INL) 1.0 1.0 VREF = VCC = 5V TA = 25C 5.0 VREF = VCC = 5V TA = 25C 0.8 0.6 0.4 0.4 ERROR (LSB) 0.6 0.2 0 -0.2 0.2 0 -0.2 3.5 3.0 2.5 2.0 -0.4 -0.6 -0.6 1.0 -0.8 -0.8 0.5 -1.0 0 28 0 156 384 512 640 768 896 1024 CODE DAC CODE = 1023 4.0 -0.4 -1.0 TA = 25C 4.5 OUTPUT VOLTAGE (V) 0.8 ERROR (LSB) Source and Sink Current Capability with VCC = 5V Differential Nonlinearity (DNL) 28 1.5 0 156 384 512 640 768 896 1024 CODE DAC CODE = 0 1 2 3 4 5 6 7 8 9 10 OUTPUT CURRENT SOURCE/SINK (mA) 0 1669 G02 1669 G01 Large-Signal Step Response 1669 G03 Midscale Glitch Load Regulation vs Output Current 1.0 5 SDA (VOLTS) 0 0.8 5V SDA 0V 5 0.6 VOUT (LSB) VCC = 5V RL = 4.7k CL = 100pF TA = 25C VOUT 10mV/DIV 1 CODE = 32 0 5s/DIV 2s/DIV 1669 G04 1.0 OFFSET ERROR VOLTAGE (mV) 0.6 VOUT (LSB) 0.4 0.2 0 -0.2 -0.4 SOURCE SINK -0.6 0 -0.2 SINK -0.8 -1.0 1669 G05 -4 -3 -2 -1 0 1 IOUT (mA) 2 3 4 1669 G06 Full-Scale Output Voltage vs Temperature 5 2.510 4 2.508 3 2.506 2 1 0 -1 -2 2.502 2.500 2.498 2.496 -3 2.494 -4 2.492 -1.0 -1.0 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1.0 IOUT (mA) -5 -60 -40 -20 0 20 40 60 TEMPERATURE (C) 80 100 1669 G08 REFERENCE SET TO INTERNAL BANDGAP 2.504 -0.8 1669 G07 SOURCE -0.6 Offset Error Voltage vs Temperature Load Regulation vs Output Current VCC = VREF = 3V VOUT = 1.5V CODE = 512 TA = 25C 0.2 -0.4 VCC = 5V RL = 4.7k CL = 100pF TA = 25C OUTPUT VOLTAGE (V) 3 VOUT (VOLTS) 2 0.8 0.4 CODE = 512 TO 511 CODE = 990 4 VCC = VREF = 5V VOUT = 2.5V CODE = 512 TA = 25C 2.490 -60 -40 -20 0 20 40 60 TEMPERATURE (C) 80 100 1669 G09 1669fa 5 LTC1669 PIN FUNCTIONS SDA (Pin 1, Pin 1 on SOT-23): Serial Data Bidirectional Pin. Data is shifted into the SDA pin and acknowledged by the SDA pin. High impedance pin while data is shifted in. Open-drain N-channel output during acknowledgment. Requires a pull-up resistor or current source to VCC. AD1 (Pin 2): Slave Address Select Bit 1. Tie this pin to either VCC or GND to modify the corresponding bit of the LTC1669's slave address. AD2 (Pin 3): Slave Address Select Bit 2. Tie this pin to either VCC or GND to modify the corresponding bit of the LTC1669's slave address. SCL (Pin 4, Pin 5 on SOT-23): Serial Clock Input Pin. Data is shifted into the SDA pin at the rising edges of the clock. This high impedance pin requires a pull-up resistor or current source to VCC. VCC (Pin 5, Pin 4 on SOT-23): Power Supply. 2.7V VCC 5.5V. Also used as the reference voltage input when the part is programmed to use VCC as the reference. AD0 (Pin 6): Slave Address Select Bit 0. Tie this pin to either VCC or GND to modify the corresponding bit of the LTC1669's slave address. GND (Pin 7, Pin 2 on SOT-23): System Ground. VOUT (Pin 8, Pin 3 on SOT-23): Voltage Output. Buffered rail-to-rail DAC output. 1669fa 6 LTC1669 DEFINITIONS Differential Nonlinearity (DNL): The difference between the measured change and the ideal 1LSB change for any two adjacent codes. The DNL error between any two codes is calculated as follows: DNL = (VOUT - LSB)/LSB Where VOUT is the measured voltage difference between two adjacent codes. Digital Feedthrough: The glitch that appears at the analog output caused by AC coupling from the digital inputs when they change state. The area of the glitch is specified in (nV)(sec). Full-Scale Error (FSE): The deviation of the actual full-scale voltage from ideal. FSE includes the effects of offset and gain errors (see Applications Information). Integral Nonlinearity (INL): The deviation from a straight line passing through the endpoints of the DAC transfer curve (Endpoint INL). Because the output cannot go below zero, the linearity is measured between full scale and the lowest code that guarantees the output will be greater than zero. The INL error at a given input code is calculated as follows: INL = [VOUT - VOS - (VFS - VOS)(code/1023)]/LSB Where VOUT is the output voltage of the DAC measured at the given input code. Least Significant Bit (LSB): The ideal voltage difference between two successive codes. LSB = VREF/1024 Resolution (n): Defines the number of DAC output states (2n) that divide the full-scale range. Resolution does not imply linearity. Voltage Offset Error (VOS): Nominally, the voltage at the output when the DAC is loaded with all zeros. A single supply DAC can have a true negative offset, but the output cannot go below zero (see Applications Information). For this reason, single supply DAC offset is measured at the lowest code that guarantees the output will be greater than zero. 1669fa 7 8 NOTE: X = DON'T CARE 2 1 SCL 3 0 0 4 0 0 5 1 AD2 ADDRESS 6 1 AD1 tr tHIGH tf tSU, DAT tHD, DAT REPEATED START CONDITION tSU, STA tHD, STA STOP CONDITION tBUF tSU, STO START CONDITION 1669 TD 7 1 AD0 8 0 WR 9 ACK 1 X X 2 X X 3 X X 4 X X 5 X X COMMAND 6 0 BG 7 0 SD 8 0 SY 9 ACK 1 1 D7 2 1 D6 3 1 D5 4 1 5 1 D3 LS DATA D4 6 1 D2 7 1 D1 8 1 D0 9 ACK 1 X X 2 X X 3 X X 4 X X 5 X X MS DATA 6 X X 7 1 D9 8 1 D8 9 ACK STOP 1669 TA02 ZERO-SCALE VOLTAGE FULL-SCALE VOLTAGE TIMING DIAGRAM VOUT 1 0 START 1 SDA 0 tLOW Typical LTC1669 Input Waveform--Programming DAC Output for Full Scale (AD2 to AD0 Set High) START CONDITION tHD, STA SCL SDA LTC1669 1669fa LTC1669 APPLICATIONS INFORMATION Write Word Protocol Used by the LTC1669 1 7 1 1 8 1 8 1 8 1 1 S Slave Address Wr A Command Byte A LSData Byte A MSData Byte A P 1669 TA03 S = Start Condition, Wr = Write Bit = 0, A = Acknowledge, P = Stop Condition Serial Digital Interface Write Word Protocol The LTC1669 communicates with a host (master) using the standard 2-wire interface. The Timing Diagram shows the timing relationship of the signals on the bus. The two bus lines, SDA and SCL, must be high when the bus is not in use. External pull-up resistors or current sources, such as the LTC1694 SMBus/I2C Accelerator, are required on these lines. The master initiates communication with the LTC1669 with a START condition and a 7-bit address followed by the Write Bit (Wr) = 0. The LTC1669 acknowledges and the master delivers the command byte. The LTC1669 acknowledges and latches the command byte into the command byte input register. The master then delivers the least significant data byte. Again the LTC1669 acknowledges and the data is latched into the least significant data byte input register. The master then delivers the most significant data byte. The LTC1669 acknowledges once more and latches the data into the most significant data byte input register. Lastly, the master terminates the communication with a STOP condition. On the reception of the STOP condition, the LTC1669 transfers the input register information to output registers and the DAC output is updated. The LTC1669 is a receive-only (slave) device. The master can communicate with the LTC1669 using the Quick Command, Send Byte or Write Word protocols as explained later. The START and STOP Conditions When the bus is not in use, both SCL and SDA must be high. A bus master signals the beginning of a communication to a slave device by transmitting a START condition. A START condition is generated by transitioning SDA from high to low while SCL is high. When the master has finished communicating with the slave, it issues a STOP condition. A STOP condition is generated by transitioning SDA from low to high while SCL is high. The bus is then free for communication with another I2C device. Acknowledge The Acknowledge signal is used for handshaking between the master and the slave. An Acknowledge (active LOW) generated by the slave lets the master know that the latest byte of information was received. The Acknowledge related clock pulse is generated by the master. The master releases the SDA line (HIGH) during the Acknowledge clock pulse. The slave-receiver must pull down the SDA line during the Acknowledge clock pulse so that it remains a stable LOW during the HIGH period of this clock pulse. Slave Address (MSOP Package Only) The LTC1669 can respond to one of eight 7-bit addresses. The first 4 bits (MSBs) have been factory programmed to 0100. The first 4 bits of the LTC1669-8 have been factory programmed to 0011. The three address bits, AD2, AD1 and AD0 are programmed by the user and determine the LSBs of the slave address, as shown in the table below: LTC1669 LTC-1669-8 AD2 AD1 AD0 0100 xxx 0011 xxx L L L 0100 000 0011 000 L L H 0100 001 0011 001 L H L 0100 010 0011 010 L H H 0100 011 0011 011 H L L 0100 100 0011 100 H L H 0100 101 0011 101 H H L 0100 110 0011 110 H H H 0100 111 0011 111 1669fa 9 LTC1669 APPLICATIONS INFORMATION Slave Address (SOT-23 Package) The slave address for the SOT-23 package has been factory programmed to be "0100 000" (LTC1669) and "0100 001" (LTC1669-1). If another address is required, please consult the factory. Command Byte Data Bytes 7 6 5 4 3 2 1 0 X X X X X BG SD SY SY 1 0 Allows update on Acknowledge of SYNC Address only Update on Stop condition only (Power-On Default) SD 1 0 Puts the device in power-down mode Puts the device in standard operating mode (Power-On Default) BG X The Bandgap (BG) bit when set to "0" selects the DAC supply voltage as its voltage reference. The full-scale output of the DAC with this setting is equal to the supply voltage. When the BG bit is set to "1," the internal bandgap reference (1.25V) is selected as the DAC's reference. The full-scale output voltage for this setting is 2.5V. 1 0 Selects the internal bandgap reference Selects the supply as the reference (Power-On Default) X Don't Care Least Significant Data Byte 7 6 5 4 3 2 1 0 D7 D6 D5 D4 D3 D2 D1 D0 Most Significant Data Byte 7 6 5 4 3 2 1 0 X X X X X X D9 D8 X = Don't care Send Byte Protocol The stop condition normally initiates the update of the DAC's output latches. Simultaneous update of more than one DAC or other devices on the bus can be achieved by reissuing new start bit, address, command and data bytes before issuing a final stop condition (which will update all the devices). An alternate way to achieve simultaneous LTC1669 updates is to override the stop condition update by setting the "SY" bit of the command byte. Setting this bit sets the device to update the DAC output latches only at the reception of a SYNC address quick command. The actual update occurs on the rising edge of SCL during the Acknowledge. In this way, all devices can update on the reception of the SYNC address quick command instead of the STOP condition. The Send Byte protocol used on the LTC1669 is actually a subset of the Write Word protocol described previously. The Send Byte protocol can only be used to send the command byte information to the LTC1669. A Shutdown (SD) bit = HIGH will put the device in a low power state but retain all data latch information. Shutdown will occur at the reception of a STOP condition. This way shutdown could be synchronized to other devices. The output impedance of the DAC will go to a high impedance state ( 500k to GND). Reception of a START or STOP condition before the Acknowledge of the command byte will cause the interrupted command byte to be ignored. 1 7 1 1 8 1 1 S Slave Address Wr A Command Byte A P S = Start Condition, Wr = Write Bit, A = Acknowledge, P = Stop Condition 1669 TA04 The Send Byte protocol is also used whenever the Write Word protocol is interrupted for any reason. Reception of a START or STOP condition after the Acknowledge of the command byte, but before the Acknowledge of the last data byte, will cause both data bytes to be ignored and the command byte to be accepted. 1669fa 10 LTC1669 APPLICATIONS INFORMATION SYNC Address/Quick Command Rail-to-Rail Output Considerations In addition to the slave address, the LTC1669 has an address that can be shared by other devices so that they may be updated synchronously. The address is called to the SYNC address and uses the quick command protocol. As in any rail-to-rail device, the output is limited to voltages within the supply range. The SYNC Address is 1111 110 Similarly, limiting can occur near full scale when VCC is used as the reference. If VREF = VCC and the DAC full-scale error (FSE) is positive, the output for the highest codes limits at VCC as shown in Figure 1c. No full-scale limiting can occur if the internal reference is used. 1 Start 7 1 1 1 1111 110 SY/CLR Ack Stop SYNC Address SY/CLR 1 0 1669 TA05 Update output latches on rising edge of SCL during Acknowledge of SYNC Address Clear all internal latches on rising edge of SCL during Acknowledge of SYNC Address The SY/CLR bit set high only has meaning when the "SY" bit of the command byte was previously set HIGH. On the otherhand, the SY/CLR bit set LOW will always clear the part, independent of the state of the "SY" bit in the command byte. Voltage Output The output amplifier contained in the LTC1669 can source or sink up to 5mA. The output stage swings to within a few millivolts of either supply rail when unloaded and has an equivalent output resistance of 85 when driving a load to the rails. The output amplifier is stable driving capacitive loads up to 1000pF. A small resistor placed in series with the output can be used to achieve stability for any load capacitance greater than 1000pF. For example, a 0.1F load can be driven by the LTC1669 if a 110 series resistance is used. The phase margin of the resulting circuit is 45 and increases monotonically from this point if larger values of resistance, capacitance or both are substituted for the values given. If the DAC offset is negative, the output for the lowest codes limits at 0V as shown in Figure 1b. Offset and linearity are defined and tested over the region of the DAC transfer function where no output limiting can occur. Internal Reference In applications where a predictable output is required that is independent of supply voltage, the LTC1669 has a user-selectable internal reference. Selecting the internal reference will set the full-scale output voltage to 2.5V. This can be useful in applications where the supply voltage is poorly regulated. Using the LT(R)1460 Micropower Series Reference as a Power Supply for the LTC1669 In applications where the advantages of using the internal reference are required but the full-scale range needs to be greater than 2.5V, an external series reference can be used. The LT1460 is ideal for use as a power supply for the LTC1669 and can provide 3V, 3.3V and 5V full-scale output voltage ranges. The LT1460 provides accuracy, noise immunity and extended supply range to the LTC1669 when the LTC1669 is operated ratiometric to VCC. Since both parts are available in SOT-23 packages, the PC board space for this application is extremely small. See Figure 2. 1669fa 11 LTC1669 APPLICATIONS INFORMATION VREF = VCC POSITIVE FSE OUTPUT VOLTAGE INPUT CODE (c) VREF = VCC OUTPUT VOLTAGE 0 512 INPUT CODE (a) 1023 OUTPUT VOLTAGE 0V NEGATIVE OFFSET INPUT CODE (b) 1669 F01 Figure 1. Effects of Rail-to-Rail Operation On a DAC Transfer Curve. (a) Overall Transfer Function (b) Effect of Negative Offset for Codes Near Zero Scale (c) Effect of Positive Full-Scale Error for Input Codes Near Full Scale When VREF = VCC 1669fa 12 LTC1669 APPLICATIONS INFORMATION 1 3.9V TO 20V 0.1F IN LT1460S3-3 2 OUT + GND 3V 0.01F 3 4 (5) VCC 5 (4) TO P 1 (1) SCL LTC1669 OUT 3 (8) 0V VOUT 3V SDA GND LTC1669 PIN NUMBERS IN PARENTHESES REFER TO MSOP PACKAGE 2 (7) 1669 F02 Figure 2. LT1460 As Power Supply for the LTC1669 1669fa 13 LTC1669 PACKAGE DESCRIPTION S5 Package 5-Lead Plastic TSOT-23 (Reference LTC DWG # 05-08-1635) 0.62 MAX 0.95 REF 2.90 BSC (NOTE 4) 1.22 REF 1.4 MIN 3.85 MAX 2.62 REF 2.80 BSC 1.50 - 1.75 (NOTE 4) PIN ONE RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.30 - 0.45 TYP 5 PLCS (NOTE 3) 0.95 BSC 0.80 - 0.90 0.20 BSC 0.01 - 0.10 1.00 MAX DATUM `A' 0.30 - 0.50 REF 0.09 - 0.20 (NOTE 3) NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 1.90 BSC S5 TSOT-23 0302 1669fa 14 LTC1669 PACKAGE DESCRIPTION MS8 Package 8-Lead Plastic MSOP (Reference LTC DWG # 05-08-1660) 3.00 0.102 (.118 .004) (NOTE 3) 0.889 0.127 (.035 .005) 5.23 (.206) MIN 0.42 0.038 (.0165 .0015) TYP 3.20 - 3.45 (.126 - .136) 0.65 (.0256) BSC 0.254 (.010) 8 7 6 5 3.00 0.102 (.118 .004) (NOTE 4) 4.90 0.152 (.193 .006) DETAIL "A" 0.52 (.0205) REF 0 - 6 TYP GAUGE PLANE 1 0.53 0.152 (.021 .006) RECOMMENDED SOLDER PAD LAYOUT DETAIL "A" 1.10 (.043) MAX 2 3 4 0.86 (.034) REF 0.18 (.007) NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX SEATING PLANE 0.22 - 0.38 (.009 - .015) TYP 0.65 (.0256) BSC 0.127 0.076 (.005 .003) MSOP (MS8) 0603 1669fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC1669 TYPICAL APPLICATION Program Up to 16 Control Outputs Per BUS and Place Them Where They Are Needed VCC = 2.7V TO 5.5V 5 4 1 VCC SMBus 1 LTC1694 + 0.1F SMBus 2 GND 2 + 5 4 VCC SCL 1 SDA 8 LTC1669CMS8 6 VOUT AD0 2 AD1 3 AD2 GND SCL P SDA 0.1F CONTROL OUTPUT 0 0V VOUT0 < VCC 7 + 5 4 VCC SCL 1 SDA 8 LTC1669CMS8 6 VOUT AD0 2 AD1 3 AD2 GND 0.1F CONTROL OUTPUT 1 0V VOUT1 < VCC 7 + 5 4 VCC SCL 1 SDA 8 LTC1669-8CMS8 6 VOUT AD0 2 AD1 3 AD2 GND 2 TO OTHER I C DEVICES 0.1F CONTROL OUTPUT 15 0V VOUT15 < VCC 7 1669 TA06 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1694 SMBus/I2C Accelerator Dual SMBus Accelerator with Active AC and DC Pull-Up Current Sources LTC1694-1 SMBus/I2C Accelerator Dual SMBus Accelerator with Active AC Pull-Up Current Only Single Rail-to-Rail 12-Bit VOUT DAC in 8-Lead MSOP Package. VCC = 2.7V to 5.5V Low Power Multiplying VOUT DAC. Output Swings from GND to REF. REF Input Can Be Tied to VCC. 3-Wire Interface. DACs LTC1659 LTC1660/LTC1664 Octal/Quad 10-Bit VOUT DACs in 16-Pin Narrow SSOP VCC = 2.7V to 5.5V Micropower Rail-to-Rail Output. 3-Wire Interface. LTC1661 Dual 10-Bit VOUT in 8-Lead MSOP Package VCC = 2.7V to 5.5V Micropower Rail-to-Rail Output. 3-Wire Interface. LTC1663 10-Bit VOUT in SOT-23, SMBUS Interface Pin Compatible with LTC1669 LTC1285/LTC1288 8-Pin SO, 3V Micropower ADCs 1- or 2-Channel, Autoshutdown LTC1286/LTC1298 8-Pin SO, 5V Micropower ADCs 1- or 2-Channel, Autoshutdown ADCs 1669fa 16 Linear Technology Corporation LT 1007 REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2007